Pages
- Advanced Features
- An Ewert Energy Systems, Inc Product
- Applicable Everywhere
- Application Notes
- Basic Features
- Battery Management System
- Comparison
- Contact Us
- Downloads & Resources
- Features
- Automotive Grade Design
- Basic Features
- Battery Compatibility
- Battery Health Monitoring
- Current Limit Calculation
- Current Sensor Support
- Field Programmable
- Fully Programmable CANBUS
- Integration with Other Devices
- Intelligent Cell Balancing
- Isolated with Fault Detection
- Multiple BMS Units in Series
- OBDII & Freeze Frame Support
- Other Features
- PC Software
- Reliability, Speed and Accuracy
- Rugged & EMI Resistant
- State of Charge With Drift
- Thermal Management
- Forum
- Frequently Asked Questions
- Media
- Products
- Purchase
- Quick Specifications
- Robust and EMI Resistant
- Site Map
- Troubleshooting
Posts
- Interfacing with Manzanita Micro Chargers
- How The BMS Works
- Interfacing with Elcon & TC Chargers
- Setting Up Torque
- Setting Up Scangauge
- Interfacing with Eltek Chargers
- Interfacing with Zivan Chargers
- Interfacing with Other On/Off Chargers
- Problems connecting to the Orion BMS unit via PC software
- Error output is on, but no error codes are present
- Cell voltages appear incorrect (not under load)
- Cell voltages appear incorrect (when under load)
- Not all cell voltages appear in live cell data
- Cell voltages drop after the charge completes
- No cell voltages are showing in the utility
- Relays don’t turn on
- Discharge or charge relay turns off too soon
- High resistance cell
- Diagnosing sudden jumps in State of Charge (SOC)
- Charger turns off before battery pack reports full state of charge
- P0A9C – Battery Thermistor Fault
- Internal resistance values are incorrect (by a significant amount)
- P0A08 – Charger Safety Relay Fault
- P0A07 – Discharge Limit Enforcement Fault
- P0A06 – Charge Limit Enforcement Fault
- P0A05 – Input Power Supply Fault
- P0560 – Redundant Power Supply Fault
- U0100 – External Communication Fault
- P0A81 – Fan Monitor Fault
- P0A02 – Weak Pack Fault
- P0A01 – Pack Voltage Sensor Fault
- P0AA6 – High Voltage Isolation Fault
- P0AFA – Low Cell Voltage Fault
- P0A1F – Internal Cell Communication Fault
- P0AC0 – Current Sensor Fault
- P0A12 – Cell Balancing Stuck Off
- P0A09 – Internal Hardware Fault
- P0A0A – Internal Heatsink Thermistor Fault
- P0A0B – Internal Software Fault
- P0A80 – Weak Cell Fault
- P0A03 – Pack Voltage Mismatch Error
- P0A04 – Open Wiring Fault (or “Open Cell Voltage Fault”)
- Setting Up EngineLink
- Using Multiple Chargers in Parallel
- Pre-Balancing Cells
- Pack voltage is reading a different voltage than measured by a voltmeter
- Replacing one or more cells
- Eltek charger isn’t charging, but should be (for standard Orion BMS)
- Brusa charger isn’t charging but should be (for standard Orion BMS)
- Generic on/off charger isn’t charging, but should be (for standard Orion BMS)
- Cells are not balancing, but should be
- EVIC Display By Andromeda Interfaces
- CANBUS Elcon Charger isn’t charging, but should be (for standard Orion BMS)
- Orion Jr. BMS does not power up (LED stays off)
- Retrieving Data With 3rd Party Devices
- Interfacing with Thunderstruck TSM2500 Chargers
- P0A0D – Cell Voltage Over 5 Volts
- Problems connecting to the Orion Jr. BMS unit via PC software
- No cell voltages appear (Orion Jr. BMS)
- Diagnosing CANBUS Communication Problems
- Intelli-Gauge Display By Andromeda Interfaces
- P0ACA – Charge Interlock Fault
- P0A0F – Cell ASIC Fault
- P0A10 – Pack Too Hot Fault
- P0A0E – Lowest Cell Voltage Too Low Fault
- P0A0C – Highest Cell Voltage Too High Fault
- Fault Code Failsafe Behavior Chart
- CHAdeMO Fast Charging Integration
- Using Parallel Strings
- Selecting The Right Current Sensor
- Using 3rd Party Thermistors With Orion BMS
- Using Nissan Leaf Modules With Orion BMS
- Interfacing with Valeo Chargers
- Interfacing with Delta-Q IC Series Chargers
- Using Tesla Battery Modules With Orion BMS
- Diagnosing J1772 Charging Related Issues
- Using the Orion BMS With Victron Equipment
- Editing Custom CANBUS Messages
- Viewing CANBUS Communication Matrix Settings
- P0AA1 – Precharge Circuit Malfunction
Archives
- May 2023 (1)
- July 2020 (1)
- May 2020 (2)
- March 2019 (2)
- February 2019 (2)
- June 2018 (5)
- January 2018 (6)
- October 2017 (1)
- March 2016 (3)
- August 2015 (1)
- July 2015 (2)
- February 2015 (1)
- January 2015 (1)
- November 2014 (1)
- October 2014 (2)
- September 2014 (1)
- July 2014 (2)
- May 2014 (4)
- February 2014 (34)
- June 2013 (3)
- January 2012 (4)
- February 2011 (1)
Categories
Sitemap created with WP Realtime Sitemap.
